this post was submitted on 30 Sep 2024
645 points (96.4% liked)
Facepalm
2672 readers
440 users here now
founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
You can also do that with a simple smart plug with energy monitoring. You can get a 4 pack for $35.
"not that iot device, use this one instead and get less function out of it"
You can get 4 ZigBee smart plugs with energy monitoring for $35. These are not IOT devices and if you just want to know if the fridge is running, these will do that, with the added benefit of allowing you to leave the fridge's WiFi disconnected, which is a security gain.
The zwave alliance disagrees that it's not an IoT platform (https://z-wavealliance.org/ Literally the title of the page calls it IoT). Also, how much power it consumes doesn't necessarily tell you if the fridge is running and it certainly doesn't tell you what the temperature inside the refrigerator is. Even a compressor pump zero refrigerant still inside the loop can consume power just spinning the motor.
Edit: Apparently saw zigbee and read zwave but the point stands https://csa-iot.org/all-solutions/zigbee/ (the standards body that controls the zigbee protocol).
IoT is essentially a catch-all marketing term, like "organic", and if I'm not mistaken, the "I" in IoT stands for "internet". ZigBee devices cannot connect to the internet. Doing so requires a hub or coordinator that contains WiFi or ethernet connectivity. There are many ZigBee coordinators that lack this functionality, which allows your data to stay local, on your own network, without exposing it to the internet.
I never claimed that a smart plug could monitor the temperature inside a fridge, but there are certainly ZigBee temperature devices you could put inside your fridge to do that, and they would work just fine.
A ZigBee smart plug with energy monitoring would certainly give you enough information to determine if the compressor had failed, as the compressor is the component that uses the most power. If the energy usage of the fridge dropped significantly, it could indicate a compressor failure. While this method isn't foolproof and won't detect all possible fridge issues, it can serve as an early warning system for major problems like compressor failure.
Refrigerators are damn near Faraday cages. Zigbee devices are going to have a hard time getting their 2.4ghz signaling out.
A failed compressor doesn't necessatily use less power. If it's simply lost pressure and hasn't seized the motor will still cycle and appear to be working from a power usage perspective.
And if the coordinator doesn't have network connectivity, how is it ever going to alert me to problems when I'm away?
I get that you're very afraid of the security implications of iot devices, but none of the ideas you're proposing are actually solutions to the problems a truly connected device can solve.
I've been using a cheap Aqara temp/humidity sensor in my fridge for years. Works fine, as I said. Many others do the same. There's a lot more plastic in fridges than you might expect.
My ZigBee devices use an ethernet based coordinator which communicates with my Home Assistant install via MQTT. The coordinator software is called Zigbee2MQTT. The coordinator does not send any data anywhere except Home Assistant.
There are many easy ways to keep your data local and private while still allowing notification when you're away from home. In my case, I pay $65/year to Nabu Casa to access my Home Assistant when I'm not at home.
I use a very similar setup to keep an eye on my mom's place from 500 miles away, including many sensors and multiple camera feeds, which are also local only with no cloud component. Frigate NVR is installed as a Home Assistant add-on, which runs detection on each camera feed and records clips when a person is detected on any feed and also pops a notification at the same time. If she wants to save a clip, she can download it, otherwise it'll be deleted after 5 days (configurable).
There are other ways to get access to local data remotely. If you don't want to pay for Nabu Casa (which funds Home Assistant development), there's also Tailscale/headscale, ZeroTier, Cloudflare, DuckDNS, reverse proxy, etc.
You could also just have Home Assistant send you an email when an event is triggered, like a rise of 2 degrees in your fridge in an hour, or a drop of 20% in energy usage over 30 minutes.
Or you could just have a notification pop in the Home Assistant app on your phone, which will work remotely with most of the methods I just listed.
EDIT: Didn't respond to your last paragraph:
I'm not "very afraid", I'm simply aware of better alternatives. Why would I risk the security of my network by giving Samsung or GE or LG a backdoor into my network when I can get most of the same information their app can give me by using cheap sensors and Home Assistant?
I'm very familiar with homeassistant, been using it for ~5-6 years. First primarily z-wave but now primarily zigbee with a tiny bit of wifi-backed matter mixed in.
That's a lot of work to replace the sensors that are built into the fridge. 2 temp sensors for the fridge and freezer separately (I'm still not convinced I wouldn't have issues with the connection being unreliable), a power clamp (you probably don't want to use a plug since the relays fail open), 2 door sensors, and a fair bit of automation to get notified, not to mention you've now added a maintenance task for all those batteries. Especially when the alternative is to connect it to the internet and you're done. I do connect my homeassistant install to their cloud service so I can get long term tracking and whatnot but the part I need is done with just the internet connection.
That's just it, with either client isolation or a dedicated and isolated IoT SSID (nearly all modern home routers have one of these) they're not actually on your network and can't communicate with any of your other devices, only the internet. I've been building enterprise networks for ~20 years now and this is how it's handled at that level and should be more than enough for a home network.
I do 100% agree for cameras though, that's all local or not at all.
Depends on the fridge, in my opinion. I don't need any door sensors because my fridge will beep at me if I leave a door open for 12 microseconds, and the freezer is pretty reliable, it's just the fridge that needs adjusting from time to time.
I just use a ThirdReality smart plug with energy monitoring primarily so I can see power consumption, but I still contend that this combined with the temp sensor is enough to let me know if there's a problem when I'm not home.
Also a 20 year IT person, but on the Linux server side. I do have an isolated network for IoT things that don't have local alternatives (pfsense hardware firewall, 24 port managed switch in the rack and ruckus APs), but I hate (hate) the enshittification of perfectly good hardware with software that exists solely to harvest my data so a corporation can have an additional revenue stream for the shareholders, and I will go pretty far out of my way to avoid giving money to companies that do this. Dreading the day my beloved dumb LG plasma TV dies.
What hardware are you running your HA instance on? Mine runs in an HAOS Proxmox VM with the USB port for the zwave dongle (for the locks) passed through. ZigBee coordinator is ethernet, so it's just plugged into a switch in the living room.