Biorix

joined 1 year ago
sorted by: new top controversial old
Everything plays with really low quality in c/[email protected]
[–] [email protected] 1 points 1 year ago (1 children)

About the IPs, Is the fact that docker is not per say on the same network can influence that ?

Everything plays with really low quality in c/[email protected]
[–] [email protected] 2 points 1 year ago* (last edited 1 year ago) (2 children)

Thanks for the response

I checked, but the issue is still there, the IPs are the same as before, as I fixed the IP of the computer on the router. The port are forwarded manually and the server is accessible from outside the network.

The limit is set to original and upload debit, limited to 11 Mbps.

I just added all the local subnetwork IP list as you said, and the option "treat IP WAN as LAN speed" was already checked.

Secure connections are set to "preferred".

Also, I'm able to access my server directly from outside through my public IP, so the forwarding should be good.

Is there a way to see if I pass through relay instead of direct local play?

10
Everything plays with really low quality (lemmy.fmhy.ml)
submitted 1 year ago* (last edited 1 year ago) by [email protected] to c/[email protected]
10 comments fedilink
 

My computer crashed recently, and I had to reinstall everything. Since then, I could not have anything above 720p anywhere besides playing directly on the computer that runs plex.

It looks like the maximum rate is 2 Mbps regardless of the original format.

I my install is pretty much the same as before.

I run plex as a docker container on Kubuntu.

CPU : I5-4590

GPU : GeForce 1030

I installed the Nvidia toolbox for docker as well, and everything should be good

I tried activating, deactivating HW transcoding, playing with the transcoding speed option, disabled the iGPU to use only the 1030, but nothing seems to make any difference.

I first thought it was a certain format, but it seems to affect everything. I tried to optimize a file by encoding it with the plex option, but the issue stays.

I thought about a network limitation, but nothing is supposed to have changed.

I'm kind of clueless now on what to do next

Any idea on where to look?

Edit2:

Solved!

I unchecked the "use relay" option, and that fixed it.

I still have issues with certain clients, but that's another problem.

I found it odd that everything defaulted to relay when it could have direct play with certain clients.

Thank you for the help!

Everything has LEDs now and they drive me nuts in c/[email protected]
[–] [email protected] 2 points 1 year ago

Yes and they are emitting a lot of light pollution. Even more than conventional lights.

Shutter Speed on Lumix G85 in c/[email protected]
[–] [email protected] 1 points 1 year ago

I do, and you're right, it was because of bracketing. I thought that this option was to set the steps of the +/- button for exposure compensation in S or A mode. I didn't think it was that, since it seems redundant with the multiple exposure option.

Anyway thanks a lot !

0
Shutter Speed on Lumix G85 (lemmy.fmhy.ml)
 

I have trouble understanding how to set a fix shutter speed with my camera.

Once I chose a SP, my camera take the picture with the right one then if I take another one shortly after it tries to adapt the shutter speed to have more or less exposure.

Is there a way to remove this option?

For info, I tried in S and M mode, with manual ISO, manual focus, manual WB, and I made sure that the "multiple exposure" option was off in the setting menu.

lemmy.fmhy.ml's stance on defederation in c/[email protected]
[–] [email protected] 24 points 1 year ago (5 children)

This is not a matter of different point of view but a moderation one, since they are outnumbered for now with flow of new people and bad actors.

I don't think they did it happily

But we're not concerned since this instance is smaller and probably not as much targeted

1
Link qBittorent docker container to VPN (lemmy.fmhy.ml)
 

I'm trying to link a docker container qFlood to my VPN (proton) on the host to prevent IP leaks.

When everything is on the host, I can just choose "proton0" in the network interface to use, but I don't know how to do that inside the container because this interface is not exposed to the container.

Is there a way to do that?

Or even to implement the VPN inside a container?

What the alternative to prevent IP leaks with qBit on docker?

Mullvad axing port forwarding, where to? in c/[email protected]
[–] [email protected] 4 points 1 year ago* (last edited 1 year ago) (4 children)

I use Proton and it pretty fast IMO even without port fowarding since I can't use it.

And it has special option that prevent tracking in the event of a warrant to get your IP and also a system to avoid streaming service blocking VPNs' addresses

My second point, if you're on Linux, don't expect all the options proposed. The Linux app is pretty bad for now. No port fowarding, no split tunneling. Just kill switch

They supposed to remake it eventually... but it's been a while

So I recommend it if your on windows or Mac.

With Linux it's usable but for the price, It's not good

That being said, you can apparently use openvpn app to use it with more options, but I hadn't have the time to try it yet.

The cli Proton is supposed to have more options but I couldn't make it work even by following the doc. I might be the problem on this one.

Edit: typo

[PSA] Communities will only show in 'All' of you instance if someone in that instance has searched and subscribed to it. in c/[email protected]
[PSA] Communities will only show in 'All' of you instance if someone in that instance has searched and subscribed to it. in c/[email protected]
[–] [email protected] 2 points 1 year ago* (last edited 1 year ago) (3 children)

That's my understanding, but I'm trying since yesterday and still no results. From Jerboa I succeeded in finding one community, but since then, it looks like I cannot even though I'm on browser right now. edit: is it possible API are overwhelmed by the number of recent requests?

[PSA] Communities will only show in 'All' of you instance if someone in that instance has searched and subscribed to it. in c/[email protected]
[–] [email protected] 6 points 1 year ago (5 children)

I'm not sure if I'm doing it correctly, but when I search for other community on other instances, it doesn't show up in the results. I tried the complete URL, the "!", the "!" plus @instance, the name alone. Is there something special to do? Is any user can look for community?

What distro(s) do you use? in c/[email protected]
[–] [email protected] 2 points 1 year ago

Same for me I really like KDE and their tools

I recently try to go with fedora KDE but Ubuntu and Red Hat is the only distro supported by Nvidia dockers toolbox