I worked out this was odd behavior on my OPNSense firewall NAT rules.
For some reason some syncing worked (eg. beehaw.org) but new connections failed. I'm not sure why. Maybe established sessions were kept alive.
Those rules haven't changed in months and months, so I'll chalk that up to "weirdness".
Yeah, I’ve tried that a couple of times too.
And run through all the federation troubleshooting steps in the docs.
I thought that, and in the past I’ve been off for a day or two and always caught up.
This time I haven’t and it’s been a week or two since coming back online.
This is more complex than you'd think because the USB spec has changed many times over the years, with updates in the connectors used, along with other sub-category changes to cables too. So there's USB versions 1, 2, 3, and 4 (and sub-versions too), along with different types of connector, eg. USB-A comes in regular and V3 (blue inside), and USB-C which is the later. Newer specs can transfer much larger amounts of data. Power Delivery (PD) is another sub-set of specification, which currently allows up to 240W of power with USB4, that's a lot, enough to charge multiple laptops at once, vastly more then the 2.5W allowed for USB 3. For more confusion there is also USB Power Delivery Programmable Power Supply, which is a sub-set to help devices negotiate charging speeds.
Another challenge - USB-C connectors can also support Thunderbolt, which gives it a whole other set of capabilities. This depends on both the cable and the port.
This explains that mess that is USB-C: https://www.androidauthority.com/state-of-usb-c-870996/
Key part:
The latest USB data speed protocols are split into several standards. There are legacy USB 1.0 and 2.0, USB 3.0, USB 3.1, USB 3.2, and the latest USB 4.0, all of which can be supported over USB-C. Confusing enough, but these have since been revised and updated to include various sub-standards, which have encompassed USB 3.1 Gen 1, USB 3.1 Gen 2, and USB 3.2 Gen 2, along with the more recent USB 3.2 Gen 1×1, USB 3.2 Gen 1×2, and USB 3.2 Gen 2×2 revisions. Good luck deciphering the differences without a handbook. Hopefully, the graph below helps.
You'd hope USB4 fixes it, but no. USB4 already boasts Gen 2×1, Gen 2×2, Gen 3×1, Gen 3×2, and Gen 4 variations, with data speeds ranging from 10 to 80 Gbps.
Cable lengths can also have an impact. The spec only allows for a specific length after which you need active cables, which include chips in them to strengthen the signal.
Several years ago a Google engineer started buying USB-C cables from Amazon and reviewing them in a lot of detail: https://www.amazon.com/gp/profile/amzn1.account.AFLICGQRF6BRJGH2RRD4VGMB47ZA
If you read some you'll see there are plenty of manufacturers who just don't even stick by the rules, so it's not always clear what you'll actually get. It doesn't help either that some products also don't play by the rules and have custom sockets that need specific vendor cables. I've had keyboards, for example, that only work with their specific vendor cables, not general USB-C ones.
This means you need to stick to a reputable set of brands, or the cables that came with the product. Decide if you need to charge something serious with it - eg. laptop, vs just a phone, watch, or small device, or whether you need data connectivity.
As another poster mentioned, just buy Anker, they're well made come with a reputable warranty, and aren't actually that expensive. Don't buy the cables you find by the supermarket/CVS checkout, or some ultra-cheap site. They might work, they might not.
Oh, and the Google engineer had his laptop fried by bad cables: https://www.engadget.com/2016-02-03-benson-leung-chromebook-pixel-usb-type-c-test.html
Last time my dishwasher died I just had to take it had and clean the pump underneath. Basically the connections apart under and had to just scrub them out. One tiny bit of plastic was gumming it up, causing some checks to fail. Stopped it running.
They’re surprisingly simple machines.
For Samsung I always buy the extended warranty. For our washer and dryer Assurion must have spent a fortune keeping them running. A lot more than I ever did to guy them. They’re only 8 years old too. It’s sad, but for Samsung they work nicely but fail frequently,
For your next one but Bosche. They’re all good, get a base model and it’ll clean well and reliably.
Given this is !privacy and the advertise as front page features both “works will all your messaging apps” and “end to end encryption”, it seems important to flag currently those aren’t mutually compatible.
It’s not their fault the apps don’t have e2e APIs, it’s a tough problem, but the secrecy and privacy guarantee is just “trust us to stick to our policy”. And they’re a start-up, tooling isn’t perfect (or even exist), mistakes happen, etc
Their self-hosting looks interesting, but then it said to use your own clients too, which took the fun out of that.
“ For example, if you send a message from Beeper to a friend on WhatsApp, the message is encrypted on your Beeper client, sent to the Beeper web service, which decrypts and re-encrypts the message with WhatsApp's proprietary encryption protocol.”
So, not really end to end for most common use-cases.
I don’t think it’s about lemmy.
curl ifconfig.io works too
I agree, that would be more authentic. Or rig up an actual line printer.
But I think the fuzzy old terminal emulator at full screen gives you a more accurate view of an old curved, flickery, low-res screen.
Event a TTY on a modern screen is going to be higher res (far more than 80x24), nice crisp fonts, colors, etc.
One way is to run Pi-hole’s admin interface on a different port. That’s configured in:
Set:
Then your URL is http://IP:8000/admin