UPDATE:
Never before have I seen an entire maker community go "WTF are you doing you MANIAC! Just frigging buy it instead". I'm impressed :-) Normally I have to solicit such a strong response, this was pure ignorance.
I don't know whether we'll go forward with the 3d-printing part of this project anymore. If we do, I do hear you on the PETG, and it's not out of the running anymore. I may take the project on in a much smaller scale, on my own dime, so I can still try out some exotic materials (ie not pla).
In response to the cost per wand. I've found mailbox red TPU72d from kungfuflex for about 43USD per kg. I made a mock-up of the wand with 2mm walls, and at 220mm length it comes out to about 54g per wand. That's about 2.5USD - if nothing goes wrong and I don't waste a spool by printing unattended.
I think there's still something to be said about being able to form the wand to fit snug on the specific flashlight. Maybe the solution will be purchasing wand attachments and making an adapter for them.
ORIGINAL POST:
I'm designing a wand attachment for a flashlight. The wand attachment will be about 170-200mm long, slightly cone shaped, and fit securely onto a given flashlight. When attached to the flashlight and the flashlight is turned on, the flashlight will illuminate the wand giving of a red glow.
The purpose of this is to use the wand for directing traffic at night. Don't worry, we're licensed to do so and typically asked by the police to do it.
See the picture for an idea of what I'm trying to explain. Disregard the tape and the fact that it's white PLA. The white PLA is what I had open and the flashlight is not the same as will be used with the final device.
The attachment will be produced in 70-150 copies and handed out to volunteers of my national guard company. The final attachment must therefore be able to take a beating, ie scratches, impacts, temperatures and various rough handling.
I have at my disposal a pool of +10 Cr6-se, one ultimaker s5 and one stratasys uprint se plus.
I'm considering a couple of material choices. TPU or PETG in a couple of the cr6s or PC in ultimaker. The uprint strictly uses some proprietary ABS spools, and all the filament I've got for that is ivory white. A buddy of mine has offered to print a release candidate in flexible tough resin. But I don't think that he has any idea about the scale of the project. So it really narrows down to TPU, PETG or PC. If I'm going to make this rigid I'm going to go for PC, for durability, or TPU for flexibility and durability.
I've found a source for PC in transparent and white and TPU (72d, 95a and 98a) in transparent, red or white.
I like the TPU72d in red, but is it the right material? I can't find anything on the translucency of opaque TPU. In the picture it's just 1 mm of opaque white PLA, but what about 2 or 3 mm of TPU? Should I just drop the illusions of red opaque TPU and print in clear PC and spray a coat of red paint on the inside? Or clear TPU?
WYD?
![](https://sh.itjust.works/pictrs/image/00cfabfb-aa03-42ed-af70-3d0da1dbd35c.webp)
I’m going to preface this with saying… you’re probably going to get a better product if you buy something mass produced. I would suggest asking a local uniform supply store (the same as served cops and security,) if they do discounts for bulk buys. They’ll usually have a few options for you.
The problem I see is weak layer adhesion leading to it snapping, unless you find some way to print it in a more horizontal orientation. The other issue is how long it’ll take to print (and wastage of failed prints,) vs cost of just buying.
It’s an economy of scale thing.
Okay, that said, I would recommend printing i red or safety-orange asa in spiral mode with a thicker extrusion width, or translucent petg.
(Edit: with translucent petg, you can have more perimeters and better light transmission, if you were doing more complicated geometry. Spiral/vase mode printing will give a single perimeter, with .6-.8mm are easily printable with a .4mm nozzle, 1mm might still be doable. 200% width will print nicely,)
TPU will be tougher and easier to put on… but it’s going to be more difficult to print reliably, IMO, and it’s probably going to have difficulty staying rigid at the thinness you need for being a traffic wand.
Side note from personal experience: stay away from the flashing/strobing modes while using it to direct traffic- it makes it hard to see the gestures when it’s dark, leading to confusion:) (and I’m guessing I don’t need to tell you how dumb people are…)
I hear you on the cost and everything else. I've updated my question to reflect this. Thanks for your input on the spiral mode, I'm going to look into getting my slicer to do that - presently I use cura 5.4.
Take your average person, how dumb are they? Half the people out there are even worse off.
So, IIRC, cura calls it 'vase mode', rather than 'spiral'. but they do the same thing. generally you can easily take extrusion widths up to 200% of your nozzle diameter before you start seeing substantial quality differences. (relatively large extrusions widths will also improve adhesion... it's one of the not-always-spoken secrets to printing water-tight vases.)
AYUP. I work as a manager for contract security. I've stopped saying "you can't get any dumber".... the universe seems to take that as a challenge.