Clamp & glue is plenty strong. I've built a couple of desks with this approach plus a large dining table.
DavidP
joined 1 year ago
We get a lot of voles which enjoy eating our garden and saplings. I've decent success by:
- garden: putting a wire mesh fence around it with 1/4" hardware cloth buried 4" underground
- trees: plastic protective tubes around the trunks and also keeping the grass/weeds around then cut short. Voles like the protection of tall grass.
Back when I started my software career (2001) we did paper code review printouts in Araxis Merge. We also didn't have source control back then.
Got a patio umbrella but didn't want to pay for a base. Have rocks, and and pail, figured I'd try making one myself.
So I have a piece of PVC secured in the bucket and then needed to lock the umbrella post into it. A person who values their time would have simply cross drilled and put in a pin, but I wanted to turn something so I made a circular wedge.
Turn a taper:
Bore for the post:
Then cut in half:
And done!
It's held up just fine in its first weekend of use.
Got a patio umbrella but didn't want to pay for a base. Have rocks, sand and pail, figured I'd try making one myself.
So I have a piece of PVC secured in the bucket and then needed to lock the umbrella post into it. A person who values their time would have simply cross drilled and put in a pin, but I wanted to turn something so I made a circular wedge.
Turn a taper:
Bore for the post:
Then cut in half:
And done!
It's held up just fine in its first weekend of use.
Got a patio umbrella and didn't want to buy a commercial base.
So I have a piece of PVC secured in the weighted bucket and needed to secure the post inside the PVC. A person who valued their time simply would have cross-drilled a hole and put a bolt through. So instead I turned a circular wedge.
Turned the taper:
Drilled for the umbrella post:
Cut in half:
Et voila
Yes this is accurate. Once our toddler understood "privacy" poop breaks became mini vacations.
Nice! Snakes are a sign of a healthy, chemical-free environment.
My cats would have loved to use the top as a scratching pad! Look out 😅
Nice work on the wrapping, it looks very clean.
Could you swap out the back legs with longer ones to help the thigh clearance?
Check the calibration:
- Confirm that the outfeed table is parallel to the cutter head.
- Confirm that the outfeed table is level with the top dead center of the cut.
- Then confirm that the infeed table is parallel to the outfeed
- Lastly confirm that the fence, when set to 90, is square to the outfeed table.
This should all the the case right out off the pallet but it's worth a check.
I relief on polled notifications from Sync. Worked just fine for me.
Awesome! Thank goodness the kiddos like the set.
Dust collection is a great application for 3D printing... Years ago I broke the bag adapter for my sanding station so I made a replacement!
Last fall I got an inexpensive 3D printer (Ender 3 Pro) and have been surprised at how it's made "shop life" better. What are your favorite things you've made for your shop? Here are mine:
Pictued above, this have 100% solved how to store these things. Just printed with PLA, they're quite strong and fit the tools perfectly.
#2: Tool Well Storage Bins
I made these to fit my bench's tool well. I had been using jars and other round containers but their shape wasted space and they didn't have internal divisions.
Nice way to keep my most often used bits out of a drawer and easy to find.
#4: 4" x 120mm Dust Hose Adapter
While not glamorous I use this every time I use my table saw.
Finally got around to making a tool Caddy for the drill press. Clearly inspired by Lee Valley's.
I have holders for all my drill bits so this is just a tray to hold small stuff used with the tool.
Here it is disassembled:
I was able to use some barrel nut hardware saved from some big box furniture kit.. Lesson to never throw that stuff away!
This old catalog has large crosscut saws (sold by the foot!). They all have a rounded "belly" on the business side and I'm wondering why.
My best guess, without just googling it, is that it widens the last strip of wood thus reducing snap offs.
So my kid has lost a bunch of these shapes and I'm going to make a replacement set.
Does anyone have any ideas for how to get a consistent roundover on the corners? I have a router table but no CNC.
The square and rectangle I could do with a roundover bit and the blocks on their sides. But I don't see any obvious solutions for the pentagon and triangle.
I'm totally fine just hand sanding these, but this kind of problem solving makes woodworking fun!
This has been my workhorse for probably five years now. It's a split top Rubou-style bench with a face vise and Veritas inset shoulder vise.
Construction is all Southern Yellow Pine. The legs are tenoned into the underside and top with stretchers in between the short sides.
In between the two top sections is a removable plane stop. When shifted to the side it sits proud to top by about a quarter inch.
The gap allows for more variety of clamping options such as supporting a long board for planing.
Spring bench dogs seen in a Paul Sellars video.
The tool well and writing surface are both removable. I needed a place to look able to sit down with my knees under the surface.
I have threaded inserts on the end for a large large planing/work stop
This is a pretty cursory description.. I'd be happy to answer any questions about it.
This is a set built-ins I did two years ago. A full one third of the project was spent painting! I did it all with a brush and regret not getting a sprayer.
cross-posted from: https://toast.ooo/post/21612
Just finished this set. Black walnut and maple blanks. The hardware is from Lee Valley .
The insert gets glued in the blank with the metal cap screwing on. I wasn't super happy with the kit because it's expensive and needs odd-sized holes. I bored undersized (7/8“) and expanded with a square end scraper, but the taper on the tubes makes it difficult to get a snug, consistent fit. Had to use some blue tape to shim the gap.
Just finished this set. Black walnut and maple blanks. The hardware is from Lee Valley .
The insert gets glued in the blank with the metal cap screwing on. I wasn't super happy with the kit because it's expensive and needs odd-sized holes. I bored undersized (7/8“) and expanded with a square end scraper, but the taper on the tubes makes it difficult to get a snug, consistent fit. Had to use some blue tape to shim the gap.
view more: next ›
We don't have any moles! The voles must keep them at bay :-)