40
Any craft store will have tiny rubber and nylon hammers for jewelry and crafts. Small Rubber and nylon mallet
What is the purpose of the two different ends instead of just having both out of rubber for example
Rubber and nylon are both soft and are less likely to damage whatever you are hammering, but rubber is even softer and bouncier than nylon. I would use rubber when pounding wooden pieces of furniture together, but nylon would work better for forming soft metal like jewelry. Other specialty hammers like brass and copper are non-sparking and non-magnetic for use around flammable gases and sensitive equipment. They continue up the hardness scale -- brass for softer applications and copper when you need more force. Finally, you have you traditional steel hammer that is usually made out of hardened steel and would really mess up that soft wood from earlier if you tried striking it directly.
You can look up "machinist hammer" usuallythry have hard plastic or rubber ends that can unscrew for alternate options. Some of them are pretty dense and tough but have good weight and don't (usually) damage anything.
Aha!!! That's exactly what I'm looking for. Thank you for the recommendation. I knew something like that must exist, but could not for the life of me figure out how to ask for it from the laughable excuse for an AI we have now.
Well I hope you find one that works! GLHF
Harbor Freight
I second this. Also ask for a rubber mallet to avoid getting snickered at
You mean a mallet? I mean home Depot or any hardware store should have some.
Probably any hardware store that has a decent tool section. Rubber mallets come in all sizes and densities.
Camping or Outdoorsy shops may have rubber mallets that are used to knock in tent pegs and similar. Not so hard as to be too easy to bend metal pegs or break plastic ones, but sturdy enough to be able to provide the force to knock them into hard ground.
Auto store. There's usually at least something available.
You can check something like woodcraft stores, but they tend to not have many hammer/mallet options when I've gone in person, and I've never really looked at their online store.
You're still likely to run into having to adapt something, rubber as a mallet material has limitations, so they tend to be no smaller than two inches in diameter, that I've ever seen. Now, plastic, I've seen as small as a half inch head, but never rubber.
Now, there are gunsmith hammers with interchangeable heads, including rubber options, and they're fairly small, but maybe too small, depends on what you're doing exactly. Too light would be just as likely. But it's an option. Those are usually available under 40USD, so feasible for a one off job, but not as cheap as automotive mallets. And you'd need you look online for those.
Can you describe the use case? Might help narrow the field of where to go (I'm assuming you checked places like amazon and didn't find what you needed, otherwise, I wouldn't have focused on the options I did for where to look)
Nylon Hammers usually are available in much smaller diameter - nylon is more dense than rubber, I believe there's a limit on his small a rubber head can be.
Or just put "something" between your hammer and the fragile wood part; I'm thinking a flip-flop sole lol.
I have the wiha 44008 with interchangable heads, it fine if you don't need different heads all the time because changing the heads takes some time.
Like a deadblow hammer?
No, a dead blow hammer is filled with shot so it doesn't bounce.
this post was submitted on 13 Mar 2024
40 points (95.5% liked)
Ask Lemmy
25325 readers
1962 users here now
A Fediverse community for open-ended, thought provoking questions
Rules: (interactive)
1) Be nice and; have fun
Doxxing, trolling, sealioning, racism, and toxicity are not welcomed in AskLemmy. Remember what your mother said: if you can't say something nice, don't say anything at all. In addition, the site-wide Lemmy.world terms of service also apply here. Please familiarize yourself with them
2) All posts must end with a '?'
This is sort of like Jeopardy. Please phrase all post titles in the form of a proper question ending with ?
3) No spam
Please do not flood the community with nonsense. Actual suspected spammers will be banned on site. No astroturfing.
4) NSFW is okay, within reason
Just remember to tag posts with either a content warning or a [NSFW] tag. Overtly sexual posts are not allowed, please direct them to either [email protected] or [email protected].
NSFW comments should be restricted to posts tagged [NSFW].
5) This is not a support community.
It is not a place for 'how do I?', type questions.
If you have any questions regarding the site itself or would like to report a community, please direct them to Lemmy.world Support or email [email protected]. For other questions check our partnered communities list, or use the search function.
Reminder: The terms of service apply here too.
Partnered Communities:
Logo design credit goes to: tubbadu
founded 1 year ago
MODERATORS